Education

2N6489 DATASHEET PDF

Posted On
Posted By admin

2N 2N 2N DESCRIPTION. ·With TO package. ·Excellent safe operating area. ·Complement to type 2N 2N 2N respectively. 2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics. 2N datasheet, 2N circuit, 2N data sheet: MOSPEC – POWER TRANSISTORS(15A,75W),alldatasheet, datasheet, Datasheet search site for.

Author: Malami Mikagis
Country: Burma
Language: English (Spanish)
Genre: Politics
Published (Last): 11 April 2012
Pages: 27
PDF File Size: 8.55 Mb
ePub File Size: 16.44 Mb
ISBN: 267-3-53234-270-4
Downloads: 86221
Price: Free* [*Free Regsitration Required]
Uploader: Tesho

However, the same considerations apply for pass elements used datashdet negative regulators. The good news is that most have been characterized, improved, and cost reduced for this application.

BOCA (BOCA SEMICONDUCTOR CORPORATION) Electronic Components Datasheet –

In fact, Vcm does influence the amplifier output voltage. A simple way of lowering the effective value of Zol is to make an impedance transformation with an emitter follower, as shown in Figure And I G is usually the lesser amount of current required to charge the gate to source capacitance through the linear region 2. It has two clear advantages over the push-pull type. For remote sense applications, the posi- tive voltage sense terminal pin 9 is connected to the positive load terminal through a separate sense lead; and the negative sense terminal the ground side of R2 is connected to the negative load terminal through a separate sense lead.

This method, however, usually ne- cessitates that separate short circuit protection be provided for the IC regulator and external pass element. For fast switching, a Motorola type 2N transistor is used. Each table lists devices that are appropriate for a given line voltage and circuit con- figuration and various power handling capabilities.

Once coCRl is found, the value of the filter capacitor, C, can be determined from: Ripple test data for various types of capacitors is shown in Table This information has been carefully checked and is believed to be entirely reliable. Since this is as low as 10 kHz for some bipolars, it is possible that a FET even with high on voltages can be competitive efficiency-wise at 20 kHz. Half-load regulation is equally impressive. However, if it is raised to a voltage above 2.

  HERNAN RIVERA LETELIER LIBROS GRATIS PDF

This complicates the selection and design task, as there are now several overlapping solutions to many of the design problems. Zener Clamp and Snubber for Single Transistor Converters Most Switchmode transistor load lines are inductive during turn on and turn off. Transformer T5 is used to reduce output switching spikes by providing common mode noise rejection, and its use is optional. Because both emitters are at an ac ground point, expensive drive trans- formers can now be replaced by lower cost capacitively coupled drive circuits.

Transistors

A selector guide of control IC’s available from Motorola is shown in Table on page The fin temperature rise, Ts – Ta, is given by: The designer may elect to use a commercially available heatsink, or if packaging or economy demands it, design his own. Input supply filter capacitor ground loop 5 If, after carefully rechecking the circuit, the designer is not successful in resolving the problem, seek assistance from the factory by contacting the nearest Motorola Sales office.

It is shorted out of the circuit by triac Ql, only after capacitors CI and C2 are fully charged, and the high frequency output transformer Tl, commences operation. Sheet Metal Figure In order to control this turn-on surge, additional resistance must often be provided in series with each rectifier.

Moreover, optocouplers drift over temperature. This latter point is the one most often made to show that systems savings are again quite possible even though the initial device cost is higher. This is particularly important in many small Figure If the transistor is turned on while energy is still being dumped into the load, the circuit is operating in the continuous mode.

Measure or calculate the inrush current at peak line voltage. The 1, watt power supply components switching transistors, transformers, and output rectifiers have been beefed up. Each of the four output stages employs one filter capacitor and one diode.

  EJB KATHY SIERRA PDF

Newer designs in the to kHz region end up at about 6: When filter capacitors are placed in series across the rectified line, as in a doubler circuit, voltage sharing can be a problem. In these cases, a clamp diode should be connected to the regulator output as shown in Figure H.

2N6489 Datasheet

The collector current mismatch can be determined by considering the following: The ultra fast is competing primarily with the Schottky in those applications where cost is more important than efficiency. Proper attention to circuit layout is therefore necessary in order to prevent regulator instability or oscillations, or degraded performance. Today’s topologies have already been challenged by the sine wave inverter, which reduces noise and improves transistor reliability, but results in a cost penalty.

Figure C shows this configuration. The classic approach is to consult manufacturers charts like the one shown in Figure and then pick a core with the required power handling ability. All other components remain cool to the touch.

2N – Bizchip Components

Root-mean-square ripple voltage for capacitor-input circuits. A partial list of companies is shown in Table Energy is coupled from the primary to the secondary of T3, forward biasing the base -emitter of Q3, and charging C3 through CR1.

In this latter case, provisions are usually made either internally or by wire “OR”-ing the outputs to convert the dual output to a single output channel. RMS and Peak repetitive rectifier current ratings can be determined from Figure Similar in many respects to the MC, the MC may also be programmed for under voltage detection 1.

Low Vp improves efficiency 2.